How We Test Power Supply Units

All power supplies have to be equipped with various protections, which also includes the system that is fed with power. You can learn more about PSU protections if you read the corresponding section of our PSUs 101 article.

The most important protections are the following:

  • Over Current Protection (OCP): The single +12V rail PSUs usually don't have OCP on this rail, but they should have OCP on the minor rails, including 5VSB.
  • Over Power Protection (OPP): Unfortunately, most PSUs have a significantly higher OPP triggering point set than their nominal max power output. This is mainly done to deal with load spikes, which could trigger OPP and shut down the system, but OPP is there for a reason, and it has to be configured correctly to serve its purpose.
  • Over Temperature Protection (OTP): Since the ATX spec recommends at least 50 °C operating temperature for continuous full-power delivery, a PSU has to have an appropriate OTP triggering point if equipped with OTP. In PSUs with only a 40 °C rating, OTP's triggering point will inevitably be lower.
  • Over/Under Voltage Protection (OVP/UVP): These protections only kick in when voltages surpass or go below a specific level. Given that the corresponding ATX limits are practically dangerous for the system's health and the fact that there is no safe way to test these protections, we decided not to deal with them, for the moment at least.
  • Short Circuit Protection (SCP): This is essential protection that all PSUs should have. If there is a short circuit in any rails, the PSU must immediately shut down.
  • Power Good Signal (PWR_OK): This signal has to drop when any of the +12V, 5V, or 3.3V output voltages go out of spec.
  • No-load Operation (NLO): The PSU must operate normally even when no load is on its outputs.
  • Surge and Inrush Protection (SIP): The design must include a Metal Oxide Varistor (MOV) or a Transient Voltage Suppression (TVS) diode, both of which protect against voltage spikes coming from the mains network. In addition, the platform must be equipped with inrush current protection. The most common way of lowering the inrush current during the PSU's start-up phase is by using an NTC (Negative Temperature Coefficient) thermistor and a bypass relay, which allows the thermistor fast cool down.

In our methodology, we consider that the OCP or OPP aren’t configured properly if their triggering points are set above 130%. Please note that a PSU might be able to deliver much more than its nominal power under normal ambient temperatures, but at higher temperatures, this won’t be the case, and if OPP is set too high then most likely the PSU will be destroyed, especially if OTP is absent. In addition, if we notice any load regulation or ripple suppression issues during our OPP tests, we consider this protection to be improperly configured.

An evaluation example of a PSU’s protection features follows.

Swipe to scroll horizontally
OCP (Cold @ 27°C)12V: 105.2A (126.29%), 11.973V
5V: 35A (140%), 5.177V
3.3V: 30.5A (122%), 3.340V
5VSB: 4.6A (153.33%), 4.959V
OCP (Hot @ 39°C)12V: 105.2A (126.29%), 11.981V
5V: 34.1A (136.4%), 5.163V
3.3V: 30.3A (121.2%), 3.340V
5VSB: 4.6A (153.33%), 4.958V
OPP (Cold @ 28°C)1239.04W (123.9%)
OPP (Hot @ 40°C)1236.02W (123.6%)
OTP✓ (151°C @ 12V Heat Sink)
SCP12V to Earth: ✓
5V to Earth: ✓
3.3V to Earth: ✓
5VSB to Earth: ✓
-12V to Earth: ✓
PWR_OKAccurate but lower than 16ms
NLO
SIPSurge: MOV
Inrush: NTC Thermistor

MORE: Best Power Supplies

MORE: All Power Supply Articles

MORE: Power Supplies in the Forums

Contributing Editor

Aris Mpitziopoulos is a Contributing Editor at Tom's Hardware US, covering PSUs.

  • JPNpower
    Nobody can fault you guys for not being thorough enough! All we can wish for is that you do these tests a bit more often. I'm at a loss how to navigate the PSU field, and a "Best Picks" section for PSU's would be tremendously helpful.
    Reply
  • Nuckles_56
    Really good article, it is now nice and clear how you guys go and test the power supplies, and as JPNpower said, no one can fault you guys for not being thorough enough.
    Reply
  • ykki
    @JPNpower= I also think a best psu for the money article would be nice but the power supplies in the market pretty much stay the same. We may go for months before seeing any change in the list.
    Reply
  • Kewlx25
    Interesting!
    Reply
  • damric
    Looks legit, Aris.

    THW used to be the laughing stock of PSU reviews, but your recent reviews have changed all of that.

    Keep up the good work!
    Reply
  • damric
    Nobody can fault you guys for not being thorough enough! All we can wish for is that you do these tests a bit more often. I'm at a loss how to navigate the PSU field, and a "Best Picks" section for PSU's would be tremendously helpful.
    @JPNpower= I also think a best psu for the money article would be nice but the power supplies in the market pretty much stay the same. We may go for months before seeing any change in the list.

    I'll make one and submit it through bb-71 to get stickied.
    Reply
  • ykki
    15570872 said:
    I'll make one and submit it through bb-71 to get stickied.

    OK. If someone makes a psu list I'd rather see it from you (or the mods). Good luck.
    Reply
  • damric
    15570891 said:
    15570872 said:
    I'll make one and submit it through bb-71 to get stickied.

    OK. If someone makes a psu list I'd rather see it from you (or the mods). Good luck.

    It will be a group effort for sure :)
    Reply
  • iam2thecrowe
    It would be nice if all manufacturers could do this testing and publish results when they build the things, or even better for it to be a requirement. Then at least there would be less junk PSU's on the market.
    Reply
  • ykki
    15571045 said:
    It would be nice if all manufacturers could do this testing and publish results when they build the things, or even better for it to be a requirement. Then at least there would be less junk PSU's on the market.
    Or more fake reviews.

    Reply